SPECIAL OFFERS - when ordering this product

Wharfedale Titan 8 150WRMS Speaker 

Send DJ Kit your Product Review now!.

Crown Audio XLS202 Amplifier 

Send DJ Kit your Product Review now!.

Wharfedale Titan 8 150WRMS Speaker

Home or road use

150 watts (rms) per speaker

2 way

8" moisture proof woofer

1" high-end titanium hf compression tweeters

Speakon inputs

Thru connections

8 ohms impedance

DtfT - high-frequency driver overload protection

Wedge shape for monitor use

Tough polypropylene moulded cabinet with rubber padded handles

Integral pole mount fitting

Multiple m8 suspension mount fittings

Rugged protective grille and top-stacking receptacles

Sophisticated linkwitz-riley 24db/octave crossover design

High-frequency eq switch (boost/flat) for long-throw applications

Very light weight

Weight: 15.3kg (including packaging)
Height: 22.0cm x Width: 27.0cm x Depth: 40.0cm
Warranty: 1 year

Crown Audio XLS202 Amplifier
The XLS Series of power amplifiers from Crown represents a new era in affordable, quality power amplification. The line consists of four models in a uniform, rugged 2U chassis, incorporating the best of tried-and-true design principles and innovative features.
The four models in the series are the XLS-202, XLS-402, XLS-602, and XLS-802. They are identical except for output power and weight.
XLS Series amplifiers are professional stereo power amplifiers engineered to meet demanding audio requirementsreliably and within budget. Plus, every XLS Series amplifier is backed by Crowns unequaled Three-Year, No-Fault, Fully-Transferable Warranty that covers everything. With over five decades of experience designing and building rock-solid products, Crown is the standard in amp technology. So check out the affordable, Crown XLS Series. They are a powerful argument for quality and value!

Specifications
XLS 202 Amplifier:
8 Ohm Stereo : 200WRMS
4 Ohm Stereo : 300WRMS
8 Ohm Bridged Mono: 600WRMS

Performance

Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25 V.

Frequency Response (at 1 watt) 22 Hz to 20 kHz: +0 dB, –0.8 dB.

Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power:
>98 dB.
No weighting, below rated power:
>93 dB.

Total Harmonic Distortion (THD): <0.5%.

Intermodulation Distortion (IMD):
(60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 0.3%.

Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.

Crosstalk (below rated power)
at 1 kHz: –76 dB. at 20 kHz: –58 dB.

Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced.

Load Impedance: Rated for 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono.

AC Line Voltage and Frequency Configurations Available (±10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC

Controls

Level: Two front-panel rotary level controls, one for each channel.

Power: Front-panel switch; on when in the IN position.

Circuit Breaker: Back-panel breaker provides overload protection.

Mode Switch: Back-panel switch selects Dual or Bridge-Mono mode.

Indicators

Signal Presence Indicators: Two green LEDs, one for each channel, illuminate when the channel’s input signal exceeds –40 dBu.

Clip Indicators: Two red LEDs, one for each channel, illuminate when the channel’s output is being overdriven.

Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available.

Fault Indicator: Two red LEDs illuminate when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on.

Input/Output

Input Connectors: One per channel; back-panel three-pin female XLR input connectors.

Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or 4-pole Speakon connectors. The top Speakon connector is wired for both channels so it can be used for bridge-mono wiring or for stereo wiring of two speakers to a single Speakon connector.
One pair of back-panel binding posts per channel; accepts banana plugs or bare wire. (European models do not accept banana plugs.)

Protection

XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and thermal protection.

Construction

Ventilation: Flow-through ventilation from front to back.

Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.

Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27 m³).

Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 15.2-inch (38.6-cm) depth.

Weight
Net Weight:
XLS-202: 23.0 lb (10.4 kg)
XLS-402: 25.7 lb (11.7 kg)
XLS-602: 29.0 lb (13.2 kg)
XLS-802: 35.5 lb (16.1 kg)

Shipping Weight:
XLS-202: 28.0 lb (12.7 kg)
XLS-402: 30.7 lb (13.9 kg)
XLS-602: 34.0 lb (15.4 kg)
XLS-802: 40.5 lb (18.4 kg)

Wharfedale Titan 8 150WRMS Speaker Downloads

Wharfedale Pro Speakers (Website Link)

Crown Audio XLS202 Amplifier Downloads

Crown Sudio XLS802, XLS602, XLS402, XLS202 Amplifiers Manual (2.88MB PDF)
Crown Sudio XLS802, XLS602, XLS402, XLS202 Amplifiers Data Sheet (361KB PDF)
Crown Audio Amplifiers (Website Link)